《MT皮纹标准Mold》由会员分享，可在线阅读，更多相关《MT皮纹标准Mold（2页珍藏版）》请在装配图网上搜索。
1、MT 皮纹标准 Mold-tech Texturing
下面所有数据来自于 Mold-Tech标准样板。
SPECIFICATIONS FOR THIS PLAQUE
MOLD MATERIAL : P-20 35RC
PLASTIC MATERIAL : GP STYRENE SURFACE PREPARATION FOR
MT MICRO FINISHES : SPI A-2
ALL SURFACE MEASUREMENTS WERE TAKEN WITH HOMMEL T-1000C
CONTACT YOUR LOCAL MOLD-TECH FACILITY REGARDI
2、NG APPLICATION OF THESE FINISHES
关于此样板说明：
模具材料：P20硬度35RC
样板材料：聚苯乙烯
表面为 MT皮纹：抛光标准 SPI A-2 采用HOMMEL T-1000C（粗糙度仪）检测表面 与当地模得制造商联系具体应用
标准编号
Rz
Rm
Tmr
MT 11001
.000105 in.
.000120 in.
N/A
MT 11002
.000210 in.
.000250 in.
N/A
MT 11003
.000195 in.
.000235 in.
N/A
MT 11004
.000
3、267 in.
.000307 in.
N/A
MT 11005
.000477 in.
.000528 in.
N/A
MT 11006
.001002 in.
.001162 in.
N/A
MT 11007
.001468 in.
.001660 in.
N/A
MT 1055-1
.00035 in.
.000420 in.
.00047 in.
MT 1055-2
.00063 in.
.000710 in.
.00080 in.
MT 1055-3
.00072 in.
.000810 in.
.00091
4、 in.
MT 1055-4
.00093 in.
.001040 in.
.00117 in.
MT 1055-5
.00097 in.
.00110 in.
.00123 in.
MT 1055
.00145 in
.00165 in.
.00185 in.
拔模角是3 5
MT 1055-6
.00179 in.
.00229 in.
.00257 in.
度，深度4
MT 1055-7
.00279 in.
.00355 in.
.00393 in.
个丝
MT 1055-8
.00310 in.
.00383 in.
5、.00467 in.
标准编号
深度
最小拔模角
MT 11000
.0004 in.
1度
MT 11010
.0010 in.
1.5度
MT 11020
.0015 in.
2.5度
MT 11030
.0020 in.
3度
MT 11040
.0030 in.
4.5度
MT 11050
.0045 in.
6.5度
MT 11060
.0030 in.
「4.5 度
MT 11070
.0030 in.
4.5度
MT 11080
.0020 in.
3度
MT 11090
.0035 in.
5.5度
MT 11100
.0060 in.
9度 —
MT 11110
.0025 in.
4度
MT 11120
.0020 in.
3度
MT 11130
.0025 in.
4度
MT 11140
.0025 in.
4度
MT 11150
.00275 in.
4度
MT 11160
.0040 in.
6度
MT皮纹标准Mold
